• Supanovakit's Avatar
    Today, 03:16 PM
    To be honest, I donít know. It was in a kit with a butane torch that I had in my garage, the solder is not labelled. Sent from my iPhone using...
    4 replies | 92 view(s)
  • Supanovakit's Avatar
    Today, 01:55 PM
    So very nearly done. I struggled to unblock the hole in the threaded boss so had to drill it through, then proceeded to solder the top back on. All...
    4 replies | 92 view(s)
  • Supanovakit's Avatar
    07-04-2021, 08:53 PM
    So as itís impossible to get new thermostats like the originals, I thought I would have a go at repairing a couple and see how I get on: ...
    4 replies | 92 view(s)
  • Supanovakit's Avatar
    07-04-2021, 08:43 PM
    Supanovakit replied to a thread Type 4 strip down in General Chat
    Thanks for the link, some great information there. Sent from my iPhone using Tapatalk
    22 replies | 630 view(s)
  • Supanovakit's Avatar
    07-04-2021, 03:09 PM
    Supanovakit replied to a thread Type 4 strip down in General Chat
    End float needs doing and will get the bearing bores checked. Sent from my iPhone using Tapatalk
    22 replies | 630 view(s)
  • Supanovakit's Avatar
    07-04-2021, 08:20 AM
    Supanovakit replied to a thread Type 4 strip down in General Chat
    So have laid out the engine parts for checking over and washing in the parts washer. A few issues to sort: Bearing for the conrods look...
    22 replies | 630 view(s)
  • Supanovakit's Avatar
    02-04-2021, 07:50 PM
    Supanovakit replied to a thread Type 4 strip down in General Chat
    All this debris sitting in the bottom of the engine, so glad I decided to strip it down. Sent from my iPhone using Tapatalk
    22 replies | 630 view(s)
  • Supanovakit's Avatar
    02-04-2021, 03:56 PM
    Supanovakit replied to a thread Type 4 strip down in General Chat
    Looks as though the last person to assemble it either didnít locate the thrust bearing correctly and tightened it down punching a new hole in it, or...
    22 replies | 630 view(s)
  • Supanovakit's Avatar
    02-04-2021, 03:28 PM
    Supanovakit replied to a thread Type 4 strip down in General Chat
    I have also taken a video of the endfloat which is a small amount with the bearing into the block but loads of float of the crank in the bearing. Is...
    22 replies | 630 view(s)
  • Supanovakit's Avatar
    02-04-2021, 03:22 PM
    Supanovakit replied to a thread Type 4 strip down in General Chat
    So today was to strip and separate the block, and itís easy to miss all the bolts that hold it together. If you are struggling to get it apart, itís...
    22 replies | 630 view(s)
  • Supanovakit's Avatar
    02-04-2021, 03:10 PM
    Supanovakit replied to a thread Type 4 strip down in General Chat
    Looks like you were right Peter, looks like evidence of a previous issue which was not cleaned out. Sent from my iPhone using Tapatalk
    22 replies | 630 view(s)
  • Supanovakit's Avatar
    02-04-2021, 01:28 PM
    Supanovakit replied to a thread Type 4 strip down in General Chat
    So, not the best thing to find in an engine. 3 pieces of aluminium, and some still rattling around in there. Struggling to get the 2 halves apart at...
    22 replies | 630 view(s)
  • Supanovakit's Avatar
    01-04-2021, 07:30 PM
    Supanovakit replied to a thread Type 4 strip down in General Chat
    Hi Mike, yeah I will dismantle them and if all looks ok will lap them in with some carborundum paste. It almost looks as if the last owner had an...
    22 replies | 630 view(s)
  • Supanovakit's Avatar
    01-04-2021, 07:23 PM
    Supanovakit replied to a thread Type 4 strip down in General Chat
    Hi Phill, Yeah It was all complete (including twin carbs) apart from the ultra rare thermostat, wheel & flap linkage, though I had these from the...
    22 replies | 630 view(s)
  • Supanovakit's Avatar
    01-04-2021, 05:15 PM
    Supanovakit replied to a thread Type 4 strip down in General Chat
    The one from the red Nova could not be saved. Too many issues with it. I got this one local for £400 complete, so worth a strip down and assess what...
    22 replies | 630 view(s)
  • Supanovakit's Avatar
    01-04-2021, 04:44 PM
    So after checking the end float on a type 4 engine I acquired, and finding it excessive, decided to strip it down and give it a thorough check over....
    22 replies | 630 view(s)
No More Results
About Supanovakit

Basic Information

Statistics


Total Posts
Total Posts
152
Posts Per Day
0.09
General Information
Last Activity
Today 06:25 PM
Join Date
23-05-2016
Referrals
0